Just How to Remove as well as Replace a Bath Tub.
Just How to Remove as well as Replace a Bath Tub.
Blog Article
Presented here in the next paragraph you can find a lot of awesome news about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't specifically rocket science, however it does need solid plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently available, the task can move rapidly; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old tub and also set in the brand-new one. Make sure you have certified on your own for the job and are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you may require a specialist plumber to make tube connections.
This article will aid you install a new tub in your washroom if you have already gotten a brand-new tub as well as do not require to change the plan of your previous water system pipelines.
Your tools and material list need to comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing taps can be rather bothersome as a result of the restricted gain access to that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. As soon as the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The previous type ought to be attached to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Making use of both wood boards under its feet, place the bathtub in the called for position. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub up until the level reviews level.
To install taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the supply of water as well as inspect all joints and also new pipework for leaks as well as tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized at least when as this will resolve it into its final position.
Planning for the Installment
First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, creating the water to permeate the wall between the bathroom and also the tiling, leading to problems with moisture and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as fittings. They are marketed in tubes and also cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the bathtub with water prior to securing, to permit the movement experienced when the bathtub remains in usage. The sealant can fracture fairly early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that post about Installing A Bathtub when doing a search on the internet. Sharing is caring. Who knows, you might be doing someone a favor. Kudos for your time. Come back soon.
Book-Now Report this page